BALL
HEAD MESH GRILLE AND WINDSCREEN FOR SHURE™ Fits
the majority of "58-style" microphones, including the Shure™
SM58, SM48, Beta 58A, SM58LC, SV100, RK143G, PGX2, Pyle™
PDMIC58, and virtually any other ball-style handheld microphone.
Replace that banged up grille today!
Part #MG-58
$6.95
Click on photo for
larger view
TUBE SHIELD BASE, REVISIT™, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM.
Our Aluminum Tube Shield Base is the perfect replacement for a damaged bayonet
"twist and lock" tube socket base. Base only - not a tube socket.
For base with socket included, see TS-9-700. Please note, we cannot
guarantee compatibility with preexisting tube shields that were installed in
your amps. However, if you have twist-lock tube shields in Fender, Orange,
Peavey, or vintage Marshall amps, this base should fit.
Part #RS-325B
$0.25
PC MOUNT TYPE
Click on photo for
larger view
PC MOUNT MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES. INCLUDES INTEGRAL
BASE FOR TWIST-LOCK TUBE SHIELD. FOR USE ON PC BOARD AMPS!
Fits
12AX7, 12AU7, 12AT7, etc. Sturdy Micalex construction, for 3/4" hole.
PC Pins. Top mounting (mounted from
the outside of the chassis), mounting holes spaced 1 1/8" apart. Designed to work with the RS-325S tube shield,
or vintage Fender™
tube shields.
Part #TS-9-700-PC
$0.99
Click on photo for
larger view
PHENOLIC TUBE SOCKET FOR OCTAL TUBES.
Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. For 1-1/8" hole.
Bottom mounting (mounted from the inside of the chassis), mounting holes spaced 1 1/2" apart.(Note: Does not fit vintage Fenders)
Part #TS-8-250
$2.59
Click on photo for
larger view
PHENOLIC TUBE SOCKET FOR OCTAL TUBES.
Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. For 1-1/8" hole.
Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/2" apart.
(Note: Does not fit vintage Fenders)
Part #TS-8-300
$2.59
Click on photo for
larger view
JACK,
9-PIN LOW PROFILE, 1/4", Marshall™, Fender™, GOLD TRIM RING
Used as the
Effects A return jack and Effects B return jack on the rear panel of the
Marshall™ DSL-50, DSL-100, TSL122 and TSL-100. Used in a
few unique Fender models. NOTE:Gold trim ring. Jack data here.
Nut and washer are included.
Replacement nut/washer set is the JN-916.
Part #J-560G
$2.75
Click on photo for
larger view
JACK, 1/4",
CHROME
NUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE, L-LEG, TIP-SLEEVE, 4 PINS, GOLD
PLATED CONTACTS.
Generally found
only in
Crate or Ampeg products.
Common input, footswitch or
effects loop jack exclusive to Crate™ and Ampeg™.
(Other brands with chrome-nut jacks use a straight pin jack such as the J-580.)
4 pins, PC mount, with
chrome nut and washer, and gold plated contacts for longer life. Note "L-Leg" pins as shown in photo.
Original Crate or Ampeg part number 39-119-01.
Part #J-580LG
$1.99
Click on photo for
larger view
USB
CONNECTOR, "B" type. USED IN YAMAHA, KORG, ROLAND, Others.
Korg part number CON0001079, as found in the Korg SV1-73, and Triton
Extreme. Also found in the Access Virus T1, Akai MPK49 and MPK61, Alesis
Q25, Q49, QX25, QX49, Dave Smith Prophet 12, Edirol PCR Series, M-Audio Axiom
49, Axiom Pro 49, Axiom 61, Axiom Pro 61, KeyRig Series, Keystation Series and
Key Studio, Roland PCR Series Controllers, and Yamaha MM6, MM8, and S90, as well
as other brands and models not listed. Line 6 part number 21-21-0001, as
found in many Line 6 guitar processors.
Part #J-437
Special Price!
$1.00
In stock
Click on photo for
larger view
USB
CONNECTOR, "A" type. USED IN YAMAHA, KORG, ROLAND,
FENDER Others.
"A" Type USB connector, found in a number of keyboards, processors,
professional audio gear made by many manufacturers. Right-angle PC
mount 4-conductor. Industry standard USB. As found
in the Fender Mustang Amp series, Korg Pa3X, Triton Extreme, Yamaha MOXF8.
Part #J-427
Special Price!
$1.00
In stock
Click on photo for
larger view
Revisit™
Quality Reproduction of Marshall™ CORNERS, FRONT OF CABINET -MATTE
SEMI-GLOSS FINISH
Front corner set, 3/4" radius. The
matte finish is much less susceptible to unsightly scratches
than a glossy finish. Rivets not included - purchase those separately. For
Marshall™
heads, combos and straight
speaker cabinets. Replace your
Marshall™
corners with quality parts at much less than Marshall™
prices.
Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #RC-1081
$4.95
(For a set of 4 front matte corners - rivets purchased separately)
Click on photo for
larger view
Revisit™
Quality Reproduction of Marshall™ CORNERS, REAR OF CABINET -MATTE
SEMI-GLOSS FINISH
Rear corner set, 3/4" radius. The
matte finish
is much less susceptible to unsightly scratches
than a glossy finish. Rivets
not included - purchase those separately. Replace your
Marshall™
corners with quality parts at much less than Marshall™
prices.
Part #RC-1080
$4.95
(For a set of 4 rear textured corners - rivets purchased separately)
Click on photo for
larger view
Revisit™
Black Plastic Stacking Corners - Set of 4
corners
For speaker cabinets and cases.
Popular "chevron" angled ridges for interlocked stacking. Screws not included - recommend the
SC-411-8 black screws for use with these corners (two packs of SC-411-8
screws needed per set of 4 corners.)
Part #BPC-834
$2.99
(Set of 4 corners)
Just 1 Set Available!
Click on photo for
larger view
NICKEL GLIDE FEET,
Revisit™,
PACK OF 4, SCREWS INCLUDED.
Nickel cover over rubber foot. 15/16" Diameter, 0.33" Tall.
Replacement for glides used on many Fender™ amplifiers, including the blackface
and silverface designs. Set of 4, includes 7/8" wood screws.
Replaces Fender™ part number 0993900000.
Made in Taiwan.
Part #SG-239
$3.95
(pack of 4 with screws)
Click on photo for
larger view
VU METER LIGHT, 12V
Large mixers with VU meters often use this as the illumination lamp for the meters.
In a dark room the meters are hard if not impossible to see if the lamp fails,
so it's a
good idea to keep a few of these on hand! 12 Volts, 250mA, 3/4 inch
long X 1/8 inch diameter. Lead length at each end 1 inch.
Part #25-455
$0.19
Click on photo for
larger view
FUSE LAMP, 6V 250mA
Fuse lamps were used to light front panels and
VU meters in classic audio receivers from the 1970s and 1980s. Found
in Marantz, Sansui, Fisher, Jvc, Protron, Lafayette, Hitachi, JVC, Panasonic,
McIntosh, Pioneer and many others. T-2 size (same size as a 3AG
fuse). Fits in fuse type clips, easy to change out with no
soldering required. Available in 6V, 8v and 12V versions.
You can determine the voltage needed by measuring the voltage across the fuse
clips. This is the 6 volt size.
Part #L-6
$0.39
Click on photo for
larger view
FUSE LAMP, 12V 150mA
Fuse lamps were used to light front panels and
VU meters in classic audio receivers from the 1970s and 1980s. Found
in Marantz, Sansui, Fisher, Jvc, Protron, Lafayette, Hitachi, JVC, Panasonic,
McIntosh, Pioneer and many others. T-2 size (same size as a 3AG
fuse). Fits in fuse type clips, easy to change out with no
soldering required. Available in 6V, 8v and 12V versions.
You can determine the voltage needed by measuring the voltage across the fuse
clips. This is the 12 volt size.
Part #L-12
$0.39
Click on photo for
larger view
SPEAKER CROSSOVER PROTECTOR LAMP
Replacement crossover tweeter protector lamp for
crossover networks. Also known as a soft protector or tweeter limiter this
device will "share" the power with your tweeter without affecting the sound or
damaging the tweeter. You will notice these flashing as they work to absorb
unwanted transients while they protect your tweeters. Festoon lamp case style.
Failure of the lamp results in no sound through the tweeter.
Dimensions: 3/8" diameter x
1-3/4" long
Part #CP-231
$3.50
LED Colors Available:
Click on photo for
larger view
5mm DIFFUSED LED - CHOICE OF COLORS
Standard 5mm (3/16") diameter diffused LED found in many guitar amplifiers
and effects pedals. Available in white, red, blue, green, or yellow. This 5mm size is commonly called the T-1-3/4
size. On LEDs the longer leg (the anode) goes to the
positive voltage supply. LEDs need a DC supply voltage and a resistor in series with them
to limit current. For a 9V supply, a 470 ohm resistor works well.
For 12 volts, a 680 ohm resistor, and for 15 volts, a 1K resistor.
Part #LED-5D
$0.29
(per LED)
LED Colors Available:
Click on photo for
larger view
3mm DIFFUSED LED - CHOICE OF COLORS
Standard 3mm (1/8") diameter diffused LED found in many guitar amplifiers
and effects pedals. Available in white, red, blue, green, or yellow. This
3mm size is commonly called the T-1
size. On LEDs the longer leg (the anode) goes to the
positive voltage supply. LEDs need a DC supply voltage and a resistor in series with them
to limit current. For a 9V supply, a 470 ohm resistor works well.
For 12 volts, a 680 ohm resistor, and for 15 volts, a 1K resistor.
Part #LED-3D
$0.19
(per LED)
Click on photo for
larger view
GRAB BAG OF POTENTIOMETER WASHERS
Approximately 2 dozen various size washers for all
sizes of pots - washers with inside diameters of 3/8", 7mm, 8mm, 9mm.
No two kits are identical.
Found in many Hartke amps as well as
other amps and pedals.
Typically used as an EQ pot. W-Taper pots are reverse audio taper
up to the midpoint, but regular audio taper past the midpoint.
Available with or without "center click detent" which marks the midpoint with a
slight click you can feel as you turn the pot. Diameter of the body of the pot is slightly smaller than a dime.
Available in the two most common values of W20K and W100K. Both
values are available with or without the center click detent.
Click on photo for more detail. INCLUDES NUT & WASHER
(For spare or replacement nut,
order the PNW-16 nut and washer set found here). Part #P-W16-XX
$1.95
RESISTOR, FLAMEPROOF,
47K OHM, 5 WATT.
Commonly used as a power supply dropping resistor in
some tube amps. Part #47KW5
$0.49
Click on photo for
larger view
WEBER AXIAL 20uf/600V
Weber axial electrolytic 20uF/600V. Used as the main filter capacitors in most brownface and blonde
Fender™ models from 1960 through 1964. The B+ voltage was greater than 500 volts in
those designs, so the regular capacitors rated at 500V are insufficient.
SPRAGUE AXIAL 25uf/50V
Replacement
for the 25uF/25V axial cathode bypass capacitors commonly found in vintage
Fender™
amps from the 1950s through the 1980s. Sprague, founded in 1926, is
considered one of the premier capacitor manufacturers in the world.
Part #SP-CAP-25-50
$4.95
Click on photo for
larger view
PANASONIC RADIAL CAPACITOR 470uF/10V
New stock of Panasonic 470uF/10V electrolytic capacitors.
Rated at 105° C. Dimensions 11.6mm H x 8.2mm D.
Part #PAN-CAP-470-10
$0.19
Click on photo for
larger view
PANASONIC RADIAL CAPACITOR 470uF/10V
New stock of Panasonic 3300uF/10V electrolytic capacitors.
Rated at 105° C. Dimensions 30.4mm H x 12.6mm D.
Part #PAN-CAP-3300-10
$0.78
Click on photo for
larger view
SUNCON (SANYO) RADIAL CAPACITOR 1200uF/10V
SUNCON is the capacitor division of Sanyo. New stock of
1200uF/10V electrolytic capacitors.
Rated at 105° C. Dimensions 16.0mm H x 10.0mm D.
Part #SUN-CAP-1200-10
$0.39
Click on photo for
larger view
SUNCON (SANYO) RADIAL CAPACITOR 1500uF/35V
SUNCON is the capacitor division of Sanyo. New stock of
1500uF/35V electrolytic capacitors.
Rated at 105° C. Dimensions 26.2mm H x 16.1mm D.
Part #SUN-CAP-1500-35
$0.99
Click on photo for
larger view
SUNCON (SANYO) RADIAL CAPACITOR 680uF/25V
SUNCON is the capacitor division of Sanyo. New stock of
680uF/25V electrolytic capacitors.
Rated at 105° C. Dimensions 16.1mm H x 10.1mm D.
Part #SUN-CAP-680-25
$0.44
Click on photo for
larger view
NIPPON CHEMICON RADIAL CAPACITOR 4700uF/63V
Class 1 4700uF/63V electrolytic capacitor,
rated at 105° C. Snap-in leads spaced at the standard 10mm distance.
Found in many solid-state guitar amps and power amps as one of the two main
filters in the power supply section. Dimensions 49.1mm H x 25.5mm D.
Part #NCC-CAP-4700-63
$2.95
Click on photo for
larger view
TRACE ELLIOT FAN™ - 12V FAN FOR SM / SMX AMPS
Original Trace Elliot™ replacement fan for SM and SMX series amps which use a 12V
fan, such as the GP7SM200, GP7SM250, etc 80mm x 80mm x 25mm (3-1/8" x 3-1/8" x
1"), 12 volts DC, 0.13 amps. Part #D08T12LWS-WS
$6.95
In stock
(Regularly $13.95)
Click on photo for
larger view
PLUG, 1/4", NEUTRIK/REAN MONO,
SOLDER TERMINALS, STRAIN RELIEF, EXTRA LARGE BODY
Commercial wide-body 1/4" mono phone plugs designed
specifically for use with heavy-gauge speaker wire. Features machined
turned brass construction, large cable clamp and solder tabs that accept up
to 12 gauge wire. 8mm cable entry. • Nickel Shell • Mfg.
#NYS225
Part #NYS225
$2.99
Click on photo for
larger view
10 ft STEREO PATCH CABLE
BY REVISIT™
Stereo balanced
1/4" connections are economical and worry-free, thanks to these
quality audio
cables featuring genuine Neutrik connectors.
Key Features:
Excellent quality, affordable cable for
connecting balanced lines
22 AWG oxygen-free copper stranded conductors
for maximum signal transfer
Premium jacket materials provide ease of
handling and long service life
5 feet in length
Part #AC-RCA35MM
$2.95
Click on photo for
larger view
RCA CABLE
6
FT DUAL RCA TO RCA BY LEVITON
Very common connection cable in audio systems to connect CD players,
tape decks, turntables to stereo receivers.
Key Features:
Made by Leviton, a well-known
manufacturer of commercial grade electrical, lighting,
energy management, audio and data networking devices.
Walmart sells this same cable in their
stores and online for $6.95.
6 feet in length
Part #AC-5451
$1.99
Click on photo for
larger view
GENUINE EMINENCE DIAPHRAGM 16
OHMS
Replacement 16-Ohm Audio Diaphragm, Titanium compression driver, 2"
diameter voice coil, 80 watts, 16 ohms impedance. 1,200Hz-20,000Hz
range. Used in many professional horn drivers, including Yamaha and Carvin.
Manufactured by Eminence.
Part #
PSD2002-16DIA
Special Price!
$22.95
Click on photo for
larger view
ROCKER SWITCH,
STANDBY,
WHITE, Genuine Marshall, FOUND IN Marshall™ JVM, JCM2000, DSL, TSL SERIES
Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40 (with
on-off standby switch only), later
versions of the DSL201 and DSL401, JVM210H, JVM410H, and JVM215C.
Has 4 electrical terminals on back of switch.1/4" push-on terminals. Rated 16A. 15/16" x 1 1/16" x 1" deep.
For the similar standby switch used in previous model series such as the
JCM-900, early versions of the TSL and DSL series, see the SW-490 switch.
This is a 2-position standby
switch - not the High-Low-Off 3-position switch used in some versions.
For the 3-position switch, see the SW-496.
This switch is priced to sell!
Part #SW-490CW
$2.95
REVISIT™
DPDT PC MOUNT TOGGLE SWITCH w/LONG BAT HANDLE
Full size handle and bushing, miniature body. PC mount.
Specifications: • Current rating: 5A @ 125 VAC, 2A @ 250 VAC • Contacts:
6 (DPDT - No center position) • Threaded bushing diameter: 12 mm (15/32") - fits
in 1/2 inch hole.
Part #SW-236L
$3.95
Click on photo for
larger view
SWITCH, SLIDE, DPDT (6
TERMINALS), MADE BY ALPHA (TAIWAN), MAY BE USED AS A REPLACEMENT FOR BRIGHT SWITCH IN 60s and 70s Fender™ AMPS.
Also used in many other applications, including some Electro Harmonix AC powered
effects pedals, such as the Memory Man. Click here
for physical specifications. Two screws are included with the
switch.
Part #SW-242S
$1.95
1 foot long!
Click on photo for
larger view
1 ft
EXTENSION CORD, 3-WIRE, 16ga, 13 Amps.
Quality extension cord for use
on stage, at home, office or workshop. Cord length is 1 ft (including plug
and socket), 16 gauge,
3-wire cord thickness is 0.31 inches (about
5/16" or 7.9mm).
Standard NEMA 5-15P plug and NEMA 5-15R single receptacle for North American use at 110-120 Volts AC,
13 amps maximum. Used only in
North America. Increases the ability of power strips to accept AC adaptors
without blocking the adjacent outlet socket! See inset photo for
more info, click on it for a larger view.
Part #EC-5296
$4.95
Click on photo for
larger view
15 AMP GROUNDED AC CONVENIENCE OUTLET WITH WIRES.
Leviton# 1374-1. Black, three-conductor outlet. Snap-mounts in 1"
square cutout. Rated 15 Amps @ 125Vac. Two 6" 14 AWG leads
and one 6" 16 AWG ground lead. UL, CSA.
Used as a
convenience outlet on the back panel of some amplifiers.
You can pick one up at Home Depot or buy on
Amazon for around $7.66. Or, buy during our Yard Sale for just
$3.79!
Part #ACS-31
$3.79
Click on photo for
larger view
TECHNICIAN'S FRIEND - "HANDY HANK"
Handy Hank is a indispensable little gadget for your pocket or tool box.
Has a bright flashlight, a 30 inch tape measure, a key chain for adding extra
gadgets, and of course, a bottle opener for those desperate times!
Compact - only 3-1/2 inches X 2 inches. Handy for musicians, stage
hands, guitar and amp techs!
DESCRIPTION: Plastic Handle
Soldering Iron
POWER CONSUMPTION: 30 Watts HEATING ELEMENT: Mica heating element TEMPERATURE RANGE: 752°-788° F VOLTAGE: 110-125 V
Part #74B30
$2.99
Click on photo for
larger view
VELLEMAN VTD-1 DESOLDERING PUMP
Remove solder with ease using the large capacity
desoldering pump by Velleman. This professional desoldering tool features
heavy-duty plastic and a long life Teflon nozzle. Simple operation with spring
powered hi-vacuum force. Measures 10.8 inches long and 0.9 inches wide.
Illustrated directions are printed on the back of the product package.
Part #VTD-1
$4.99
Click on photo for
larger view
JACK PLATE, BLACK METAL
For two Neutrik™
NL4MP speakON™
connectors
Steel dish pre-punched. Constructed of heavy-duty 1.2
mm/.047" steel. Black oxide finish. Jacks not included - order
separately. Dimensions: 4" x 4 3/8".
See full dimensions here
Part #JP-028
$2.95
Click on photo for
larger view
JACK PLATE, BLACK METAL
For two Neutrik™
NL4MP speakON™
connectors and two 1/4" jacks.
Steel dish pre-punched. Constructed of heavy-duty 1.2
mm/.047" steel. Black oxide finish. Jacks not included - order
separately. Dimensions: 5-1/8" x 3-1/2".
Part #JP-602
$2.95
Click on photo for
larger view
JACK PLATE, BLACK METAL
For two Neutrik™
NL4MP speakON™
connectors .
Steel dish pre-punched. Constructed of heavy-duty 1.2
mm/.047" steel. Black oxide finish. Jacks not included - order
separately. Dimensions: 5-1/8" x 3-1/2".
Part #JP-604
$2.95
Click on photo for
larger view
JACK PLATE, BLACK METAL
For one Neutrik™
NL4MP speakON™
connector .
Steel dish pre-punched. Constructed of heavy-duty 1.2
mm/.047" steel. Black oxide finish. Jacks not included - order
separately. Dimensions: 4" x 4 3/8"
Part #JP-949
$2.95
Click on photo for
larger view
JACK PLATE, BLACK METAL
For two Switchcraft #11 jacks and two Neutrik™ NL4MP speakON™ connectors.
This allows you to connect to the cabinet via speakON™ connectors or 1/4" plugs.
Constructed of heavy-duty 1.2 mm/.047" steel. Black oxide finish. Jack not
included - order separately. Dimensions: 4" x 4 3/8".
See full dimensions here
Part #JP-322
$2.95
Click on photo for
larger view
DALCO SMALL COMPRESSION SPRING KIT
Originally used in VCR idlers, these multiple size compression springs are
useful in the shop for a variety of projects. Smallest size has a
wire diameter of 0.4 mm, a coil diameter of 4.3 mm, and 5 layers to the spring.
The largest has a wire diameter of 0.75 mm, coil diameter of 11.0 mm, and 6
layers in the spring. 16 different sizes, 5 springs of each
size for a total of 80 springs.
Part #09-1007
$1.99
Click on photo for
larger view
STK5468 VOLTAGE REGULATOR, FOR VIDEO RECORDERS
Input: 30 Volt DC
Output 1: 12.8 Volt DC 1.0 Ampere
Output 2: 12.1 Volt DC 1.0 Ampere
Output 3: 5.3 Volt DC 1.0 Ampere
Part #STK5468
$4.95
AUDIO / VIDEO TAPE SPLICING KIT
The most frustrating thing about splicing tape is
holding it in position. This jig fixes that problem!
Designed for both 1/2" video tape and 1/4" cassette tape. Includes
splicing tape and additional leader tape for VHS and Beta cartridges.
Note: Razor blade is not included for safety reasons - supply your
own single-edge razor blade.
Part #TAPE-SPLICE-KIT
$3.95
Click on photo for
larger view
KSS-213C CD OPTICAL PICKUP
The KSS-213C pickup has a 3.86mm focus length,
0.45 NA, 2.1mm working distance, 760-800nm laser, 200mA RMS focusing coil, and
2V laser diode reverse voltage.
Click here for a partial list of CD makes and
models which use this optical pickup.
This CD pickup is currently selling on Amazon for
$34.50.
Part #KSS-213C
$17.25
Click on photo for
larger view
6 FT COAX CABLE, RCA PLUG AT ONE END, BNC AT
THE OTHER END. RG59U CABLE.
Used for video connections to some commercial
quality VCRs and televisions. 6 ft in length.
Part #RCABNC-6
$4.95
Click on photo for
larger view
A-7040-474-C GEAR SET, FOR CERTAIN SONY VCRs
Used in some Sony SLV series VCRs.
Kit contains 3 gears and one slide plate. Common failure item.
Part #A-7040-474-C
$6.95
Click on photo for
larger view
PANASONIC
VMMS0105 SLIDE ROD - ALSO USED AS RCA
225141 SLIDE PLATE, FOR CERTAIN RCA, GE AND PANSONIC VCRS
Used in a number of RCA, GE, and Panasonic VCRs
from the 1990s
Inset picture shows the bottom of the VCR chassis which used this slide plate.
See VCR models which use this part here
Part #VMMS0105
$6.95
Click on photo for
larger view
SHARP NPLYV0107GEZZ IDLER / CLUTCH ASSEMBLY
ALSO REPLACES NPLYV0111GEZZ
Replaces the idler assembly in many Sharp VCRs
from the 1980s.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
Revisit™
Quality Reproduction of Marshall™ CORNERS, FRONT OF CABINET -MATTE
SEMI-GLOSS FINISH
Tube
Amp Doctor™
80uF/450V ELECTROLYTIC AXIAL CAPACITOR
NIPPON CHEMICON RADIAL CAPACITOR 4700uF/63V
TRACE ELLIOT FAN™ - 12V FAN FOR SM / SMX AMPS
10 ft STEREO PATCH CABLE
BY REVISIT™ 
RCA CABLE
6
FT DUAL RCA TO RCA BY LEVITON
ROCKER SWITCH,
STANDBY,
WHITE, Genuine Marshall, FOUND IN Marshall™ JVM, JCM2000, DSL, TSL SERIES
REVISIT™
DPDT PC MOUNT TOGGLE SWITCH w/LONG BAT HANDLE
SWITCH, SLIDE, DPDT (6
TERMINALS), MADE BY ALPHA (TAIWAN), MAY BE USED AS A REPLACEMENT FOR BRIGHT SWITCH IN 60s and 70s Fender™ AMPS.
PANASONIC
VMMS0105 SLIDE ROD - ALSO USED AS RCA
225141 SLIDE PLATE, FOR CERTAIN RCA, GE AND PANSONIC VCRS
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 
